16000mAh 22.2V 6S High Discharge Drone Battery Pack for UAV and Agricultural Aircraft — 30C LiPo with XT-90S

This high discharge drone battery pack (model OID7379186-16000mAh-22.2V-30C-0105) is built for professional UAV operators who need dependable power under heavy load. The 6S configuration delivers 22.2V nominal with 16000mAh capacity, while the 30C high-rate cell design supports continuous 70A and peak 90A discharge through the XT-90S connector. Each pack ships with a JST-XH-7P waterproof charging plug, black heat-shrink sleeve, magic strap, and transparent PVC outer wrap. The low internal resistance and stable output make this battery well suited to agricultural plant protection drones and other high-performance aerial platforms.

• High-rate discharge design: 70A continuous and 90A peak at pack level with cells rated for up to 240A continuous and 480A peak.
• 30C instantaneous support: engineered for short bursts of high power during demanding flight phases.
• Low internal resistance: initial pack impedance of 15mOhm or less for efficient power delivery and less heat buildup.
• Stable output: consistent performance across a wide operating temperature window and over 90 percent capacity retained after 30 days of storage.
• Long service life: 500 or more cycles with at least 80 percent capacity retention under specified test conditions.
• Mechanical durability: passes vibration, drop, over-discharge, and over-charge tests without fire or leakage.
• UAV-focused build: high-current XT-90S discharge wiring and a reliable JST-XH-7P charging connector selected for professional drone use.

Jianheng provides a 12-month warranty from the shipment date covering defects in materials and workmanship under normal use. Coverage requires that the battery is used, charged, and stored according to the specifications in this document, and that it has not been disassembled, modified, physically abused, immersed in water, or repaired by unauthorized parties. Damage from improper charging, over-discharge, over-current, external short circuit, or use outside the stated operating limits is excluded. Jianheng's obligation is limited to repair or replacement at its discretion and does not extend to incidental or consequential damages.

Q: How should this high discharge drone battery pack be charged?

A: Use the standard method: 0.5C constant current to 25.2V, then constant voltage at 25.2V until the current falls to 0.02C or less. The maximum charge current is 3.0C at 23 plus or minus 5 degrees C. Always use a charger designed for this specification.

Q: What are the continuous and peak discharge ratings?

A: The pack supports up to 70A continuous and 90A peak, limited by plug and wire. The cells themselves can handle up to 240A continuous and 480A peak.

Q: How should the pack be stored long term?

A: Store at 23 plus or minus 5 degrees C and 65 plus or minus 20 percent RH with voltage between 21.6V and 23.4V. Recharge once every 3 months and keep the pack at roughly 50 percent charge. The storage temperature range is -20 degrees C to 40 degrees C.

Q: What cycle life can I expect?

A: The pack is rated for 500 or more cycles with at least 80 percent capacity retention under the specified test conditions (charge 1C to 25.2V; discharge 5C to 19.8V).

Q: What safety tests does this battery pass?

A: It passes vibration, drop, over-discharge, and over-charge tests without fire or leakage, and includes a PCM for overcharge, over-discharge, and over-current protection.

Q: Which connectors are fitted?

A: The discharge side uses an XT-90S female connector with UL3135# 10AWG wire, exposed length 150 plus or minus 10mm. The charging side uses a JST-XH-7P reverse-direction waterproof plug with UL3239# 22AWG wire, exposed length 150 plus or minus 10mm.

Q: What is the shipment voltage?

A: The shipment voltage is 23.1V or higher.

Q: What certifications are available?

A: The battery is certified to UN38.3 and comes with an MSDS.

The battery pack shall be stored within -20 degrees C to 40 degrees C. For long-term storage (more than once every three months must fill the electricity), the environmental condition should be: temperature 23 plus or minus 5 degrees C, humidity 65 plus or minus 20 percent RH. The voltage for long-term storage shall be 21.6V to 23.4V. The battery should be charged once every 3 months and kept at about 50 percent charge state. During transportation, the battery should be kept away from water, fire sources, and strong impacts. The product should be packed properly to prevent short circuits and mechanical damage. The shipment voltage is greater than or equal to 23.1V.

• Do not put the product into water.
• Do not use the product near fire sources or heat sources.
• Do not disassemble or modify the product without authorization.
• Do not smash or strongly impact the product.
• Please charge with a special charger designed to meet the requirements of this specification.
• The charge current and charge voltage must not exceed the maximum values specified in this specification.
• The charger design should meet the requirements of this specification. Using current and voltage ranges beyond the requirements of this specification may cause quality problems in battery charge and discharge performance, mechanical performance, and safety performance.
• The cell/battery pack shall be equipped with a PCM that can properly protect the cell/battery pack. The PCM shall have functions of (1) overcharging prevention, (2) over-discharging prevention, and (3) over-current prevention to maintain safety and prevent significant deterioration of cell performance. Over-current can occur by external short circuit.
• Do not expose batteries to direct sunlight.
• The above warnings are based on the danger of using the battery. The user will take full responsibility for the result of using this battery.