This 6S LiPo pack is configured for professional UAVs that draw high current. Model OID7379186-16000mAh-22.2V-30C-0105 uses six series cells to deliver 22.2V nominal and 16000mAh nominal capacity. The 30C high-rate design supports a 70A continuous / 90A peak pack discharge through an XT-90S connector. Each unit includes a JST-XH-7P reverse-direction waterproof charging plug, black heat-shrink sleeve, English label, magic strap, and transparent outer PVC wrap. It is intended for agricultural aircraft and other demanding aerial platforms.
| Parameter | Value | Note |
|---|---|---|
| Charge Cut-off Voltage | 25.2V | Cell voltage less than 4.25V |
| Nominal Voltage | 22.2V | |
| Discharge Cut-off Voltage | 18.0V | |
| Nominal Capacity | 16000mAh | At 0.5C discharge |
| Minimal Capacity | 15900mAh | At 0.5C discharge |
| Standard Charging Method | 0.5C CC charge to 25.2V, then CV 25.2V until charge current declines to less than or equal to 0.02C | |
| Max Charge Current | 3.0C | At 23 plus or minus 5 degrees C |
| Continuous Discharge Current | 70A | Determined by plug and wire; battery cells can be up to 240A |
| Peak Discharge Current | 90A | Determined by plug and wire; battery cells can be up to 480A |
| Operating Temperature - Charging | -10 degrees C to 40 degrees C | |
| Operating Temperature - Discharging | -20 degrees C to 55 degrees C | |
| Initial Impedance | Less than or equal to 15mOhm | Internal resistance measured at AC 1KHz after 50 percent charge |
| Weight | About 2100g | |
| Storage Temperature - 1 Month | -20 degrees C to 40 degrees C | At shipping status: approx. 50 percent capacity of fully charged state |
| Storage Temperature - 3 Months | -10 degrees C to 35 degrees C | At shipping status: approx. 50 percent capacity of fully charged state |
| Storage Temperature - 1 Year | 22 degrees C to 28 degrees C | At shipping status: approx. 50 percent capacity of fully charged state |
| Storage Maintenance | The battery should be charged once every 3 months, keep its charge state at about 50 percent | |
| Voltage Difference | Less than or equal to 50mV per 30 days | To spurt the code date shall prevail |
| Shipment Voltage | Greater than or equal to 23.1V | |
| Battery Model | P1174170S4 | |
| Cell model Configuration | 6S | |
| Discharge Connector | XT-90S female connector, UL3135# 10AWG, exposed wire length 150 plus or minus 10mm | |
| Charging Connector | JST-XH-7P reverse-direction waterproof plug, UL3239# 22AWG, exposed wire length 150 plus or minus 10mm | |
| Packaging | One-side wiring, black heat-shrink sleeve, English label, magic strap, outer transparent PVC wrap |
| Item | Value | Tolerance | Note |
|---|---|---|---|
| Thickness (T) | Less than or equal to 73mm | Battery pack thickness | |
| Width (W) | Less than or equal to 79mm | Battery pack width | |
| Height (H) | Less than or equal to 186mm | Battery pack height | |
| Weight | About 2100g | ||
| Discharge Wire Length | 150 plus or minus 10mm | plus or minus 10mm | XT-90S female connector, UL3135# 10AWG |
| Charging Wire Length | 150 plus or minus 10mm | plus or minus 10mm | JST-XH-7P reverse-direction waterproof plug, UL3239# 22AWG |
| Item | Condition | Result |
|---|---|---|
| Capacity | According to the charge by standard method 2.6, 0.5C discharge to 18V cut-off voltage | Greater than or equal to 15900mAh |
| Cycle Life | Charge: 1C to 25.2V (cell voltage less than 4.25V); Discharge: 5C to 19.8V; 80 percent or more of 1st cycle capacity at 0.5C discharge | Greater than or equal to 500 cycles |
| Self-discharge | According to the charge by standard method 2.6, stored at 23 plus or minus 5 degrees C for 30 days, then measured capacity with 0.5C till 18V | Residual capacity greater than 90 percent |
| Temperature Characteristics - -10 degrees C | Charged by standard method 2.6, discharged at 0.5C to 18V at different temperatures; percentage based on discharge capacity at 23 degrees C | Capacity retention greater than or equal to 80 percent |
| Temperature Characteristics - 0 degrees C | Charged by standard method 2.6, discharged at 0.5C to 18V at different temperatures; percentage based on discharge capacity at 23 degrees C | Capacity retention greater than or equal to 85 percent |
| Temperature Characteristics - 50 degrees C | Charged by standard method 2.6, discharged at 0.5C to 18V at different temperatures; percentage based on discharge capacity at 23 degrees C | Capacity retention greater than or equal to 95 percent |
| High Temperature Performance | Charged by standard method 2.6, placed at 55 plus or minus 2 degrees C for 4 hours, then discharged at 0.5C to 18V | Capacity recovery rate greater than or equal to 85 percent (based on nominal capacity); thickness less than or equal to 10 percent |
| Vibration Test | Charged by standard method 2.6, fixed to vibration table, frequency varied at 1Hz per minute between 10Hz and 55Hz, excursion 1.6mm, vibrated for 30 minutes per axis of XYZ axes | No fire, no leakage |
| Drop Test | Charged by standard method 2.6, dropped from 1 meter height onto 20mm thick hard board, X, Y, Z positive and negative directions (six directions), free fall once per direction | No fire, no leakage |
| Over-discharge | Charged by standard method 2.6, discharged at 1C to 0V | No fire, no leakage |
| Over-charging | Battery with thermocouple placed in fume hood, connected to constant current and constant voltage source, adjusted to 1C2A, voltage set to n times 4.5V, charged until battery voltage is n times 4.5V and current drops to near 0A; experiment ended when battery temperature drops to about 10 degrees C below peak | No fire, no leakage |
Jianheng covers this battery for 12 months from shipment against material and workmanship defects when used normally. The battery must be handled, charged, and stored in line with the published specification and must not be dismantled, altered, abused, submerged, or serviced by unauthorised personnel. Exclusions include damage caused by improper charging, over-discharge, over-current, external short circuit, or operation outside stated limits. The remedy is limited to repair or replacement at Jianheng's discretion, without liability for incidental or consequential loss.
Q: How is this high discharge drone battery pack charged?
A: Use 0.5C constant current to 25.2V, then constant voltage at 25.2V until current falls to 0.02C or less. Maximum charge current is 3.0C at 23 plus or minus 5 degrees C. Use a compatible charger.
Q: What discharge ratings apply?
A: The pack supports 70A continuous and 90A peak, subject to plug and wire. The cells are rated up to 240A continuous and 480A peak.
Q: What cycle life is specified?
A: 500 or more cycles with at least 80 percent retention under specified conditions (1C charge to 25.2V; 5C discharge to 19.8V).
Q: Which connectors are fitted?
A: The discharge side uses an XT-90S female connector with UL3135# 10AWG wire and 150 plus or minus 10mm exposed length. The charging side uses a JST-XH-7P reverse-direction waterproof plug with UL3239# 22AWG wire and 150 plus or minus 10mm exposed length.
Q: What is the shipment voltage?
A: The shipment voltage is 23.1V or higher.
Q: What certifications are supplied?
A: The battery is certified to UN38.3 and supplied with an MSDS.
The battery pack shall be stored within -20 degrees C to 40 degrees C. For long-term storage (more than once every three months must fill the electricity), the environmental condition should be: temperature 23 plus or minus 5 degrees C, humidity 65 plus or minus 20 percent RH. The voltage for long-term storage shall be 21.6V to 23.4V. The battery should be charged once every 3 months and kept at about 50 percent charge state. During transportation, the battery should be kept away from water, fire sources, and strong impacts. The product should be packed properly to prevent short circuits and mechanical damage. The shipment voltage is greater than or equal to 23.1V.