Built for high-current drone power systems, this Jianheng LiPo cell combines a 5000mAh 3.7V rating with a 75C peak discharge class. It is intended for UAV battery pack fabrication and comparable high-drain drone projects. The low-impedance design helps manage short burst loads, while cold-weather discharge behavior and repeatable manufacturing make it suitable for B2B pack builders.
During pack design, the cell is specified at 3.7V nominal with 4.2V charge and 3.0V discharge limits. Standard charge and discharge are both 2.5A (0.5C) at 25C. If the build uses a high-voltage UAV battery pack layout, treat the 375A (75C) discharge figure as a short-duration limit of ≤20 seconds, not a continuous rating.
At low temperature, capacity remains at least 65% at 0C and at least 50% at -10C when discharge is 0.5C. Charging below 0C is not allowed. Vibration and 1m drop testing are also covered under the stated criteria, with no leakage, explosion, or fire.
Use a charger designed for lithium-ion cells only. At 25C, the standard charge is 2.5A (0.5C). The 10A (2.0C) higher rate is permitted only when ambient temperature stays between 20C and 45C. Do not let charge voltage exceed the 4.2V cut-off.
Yes. Low-temperature discharge is part of the cell design. At 0.5C discharge, at least 65% capacity is kept at 0C and 50% at -10C. Charging below 0C is not permitted.
The peak discharge rating is 375A (75C) and may last only up to 20 seconds. Continuous standard discharge is 2.5A (0.5C). Going beyond the current or time limit can harm the cell and void the warranty.
If storage will exceed 3 months, use a cool, dry place at -20C to +35C and 65±20% RH. For one-year storage, -20C to +25C is advised. Every 3 months, perform an activation cycle: charge at 0.2C to 4.2V, discharge to 3.0V, then charge to 3.7V.
With standard charge and discharge, more than 80% of rated capacity should remain after 300 cycles. Suitable handling and storage conditions help extend service life.
If swelling, odor, or overheating occurs, stop use at once and remove the battery from the device or charger. Do not open or puncture the cell. Ask the supplier for disposal or replacement guidance.
Do not combine this battery with other lithium-ion or polymer models. For series or parallel arrangements, use identical batteries to reduce imbalance and safety risk.
| Parameter | Specification |
|---|---|
| Typical Capacity | 5.0Ah (5000mAh) |
| Minimum Capacity | 4.8Ah (0.2C discharge to 3.0V at 25C) |
| Nominal Voltage | 3.7V |
| Charge Cut-off Voltage | 4.2V |
| Discharge Cut-off Voltage | 3.0V |
| Standard Charge Current | 2.5A (0.5C) at 25C |
| Maximum Charge Current | 2.5A (0.5C) at 0~20C; 10A (2.0C) at 20~45C |
| Standard Discharge Current | 2.5A (0.5C) |
| Maximum Discharge Current | 375A (75C) for <= 20 seconds |
| Internal Impedance | ≤ 2.5mOhm (AC 1kHz) |
| Shipment Voltage | 3.7~3.9V |
| Weight | Approx. 115g |
| Thickness (T) | ≤ 7.5mm |
| Width (W) | ≤ 49.0mm |
| Height (Length) (H) | ≤ 146.0mm |
| Tab Center Distance (L1) | 23 ± 2mm |
| Tab Length (L2) | 10 ± 2mm |
| Tab Width (L3) | 16 ± 0.2mm |
| Test Item | Criterion |
|---|---|
| Internal Impedance | ≤ 2.5mOhm (after standard charge) |
| Initial Capacity | ≥ 4.8Ah (standard charge and discharge) |
| Discharge at 55C | ≥ 90% of rated capacity |
| Discharge at 0C | ≥ 65% of rated capacity |
| Discharge at -10C | ≥ 50% of rated capacity |
| Cycle Life | ≥ 300 cycles to 80% of rated capacity |
| Shelf Life (28 days at 25C) | Retention ≥80%, Recovery ≥85% |
| Shelf Life (7 days at 55C) | Retention ≥75%, Recovery ≥80% |
| Vibration Test | Voltage change ≤0.3V, Resistance change ≤20%, no leakage |
| Drop Test | No explosion, fire, or leakage (1m drop) |
This model complies with UN38.3 transportation safety standards and includes MSDS documentation. It has passed rigorous vibration and drop tests without explosion, fire, or leakage.
| Storage Duration | Recommended Environment |
|---|---|
| < 3 months | -20C ~ +45C, 65±20% RH |
| > 6 months | -20C ~ +35C, 65±20% RH |
| Optimal (1 year) | -20C ~ +25C, 65±20% RH |