This OID13119358-120000mAh-3.7V-3C-0112 lithium polymer cell is intended for professional UAV battery pack integration. It pairs a 123.0Ah typical capacity, 120.0Ah minimum capacity, 3.7V nominal voltage and 421Wh/kg average energy density with a low ACIR of less than or equal to 1.0 milliohm at 1kHz. Pack builders can use it where predictable energy delivery and current headroom are needed for long-endurance drone platforms.
| Parameter | Value | Note |
|---|---|---|
| Capacity (Typical) | 123.0Ah | 0.2C at 4.3V to 2.5V at 25 plus or minus 2 degrees C |
| Capacity (Minimum) | 120.0Ah | 0.2C at 4.3V to 2.5V at 25 plus or minus 2 degrees C |
| ACIR at 1KHz | Less than or equal to 1.0 milliohm | 40% SOC at 25 plus or minus 2 degrees C |
| Average Weight | 1080.0g plus or minus 3.5% | |
| Average Energy Density | 421Wh/kg | |
| Charge Cut-off Voltage | 4.3V | |
| Discharge Cut-off Voltage | 2.5V | |
| Nominal Voltage | 3.7V | 0.1C at 4.3V to 2.5V at 25 plus or minus 2 degrees C |
| Operating Temperature - Charge (0 to 5 degrees C) | 0.1C (max) to 4.3V | |
| Operating Temperature - Charge (6 to 15 degrees C) | 0.2C (max) to 4.3V | |
| Operating Temperature - Charge (16 to 24 degrees C) | 0.3C (max) to 4.3V | |
| Operating Temperature - Charge (25 to 35 degrees C) | 0.5C (max) to 4.3V | |
| Operating Temperature - Charge (36 to 45 degrees C) | 0.2C (max) to 4.3V | |
| Standard Charge Method | 0.2C CC to 4.3V, 4.3V CV to 0.02C | |
| Standard Discharge Method | 0.2C | |
| Max Charge Current | 0.5C (continuous) | |
| Max Discharge Current | 2.0C (continuous) | SOC greater than or equal to 15%; Voltage greater than or equal to 2.9V |
| Max Pulse Discharging Current | 3.0C/30s | SOC greater than or equal to 50% |
| Storage Temperature (40% SOC, 12 months) | -20 to 25 degrees C at 80% RH max | |
| Storage Temperature (40% SOC, 3 months) | -20 to 35 degrees C at 80% RH max | |
| Storage Temperature (40% SOC, 1 month) | -43 to 45 degrees C at 80% RH max |
Measured without scales, the cell has 11.8mm max thickness at 40% SOC and 13.5mm max thickness at 100% SOC for fresh cells. Width is 119.0mm max and length is 358.0mm max.
| Item | Value | Tolerance | Note |
|---|---|---|---|
| Thickness (T) | 11.8 max mm | 40% SOC, fresh cell | |
| Thickness (T) | 13.5 max mm | 100% SOC, fresh cell | |
| Width (W) | 119.0 max mm | ||
| Length (L) | 358.0 max mm | ||
| Sealant Length (A) | 0.5 to 3.0 mm | ||
| Tab Width (B) | 80.0 plus or minus 0.2 mm | plus or minus 0.2 mm | |
| Tab Thickness (Aluminum) | 0.40 plus or minus 0.02 mm | plus or minus 0.02 mm | |
| Tab Thickness (Copper Nickel-plated) | 0.30 plus or minus 0.02 mm | plus or minus 0.02 mm | |
| Top Sealing Width (C) | 14.0 plus or minus 1.0 mm | plus or minus 1.0 mm | |
| Tab Distance Battery Edge (L1) | 19.3 plus or minus 2.0 mm | plus or minus 2.0 mm | |
| Tab Length (L2) | 22.0 plus or minus 2.0 mm | plus or minus 2.0 mm |
Validation covers appearance, dimensions, weight, shipment voltage, initial internal impedance, discharge capacity, leakage, external short circuit and over-discharge checks. The protected reference data remains in its placeholder.
| Item | Condition | Result |
|---|---|---|
| Appearance | Visual inspection | No defects and no leakage |
| Dimension | Caliper measurement | According to item 4 |
| Weight | Balance measurement | According to item 3.3 |
| Shipment Voltage | Voltmeter measurement | 3.30 to 3.60V (40% SOC) |
| Initial Internal Impedance | AC impedance at 1kHz, 40% SOC | Less than or equal to 1.0 milliohm |
| Discharge Capacity | Standard charge followed by standard discharge at 25 plus or minus 2 degrees C | Minimum 120.0Ah |
| Cycle Life | 0.2C CC charge to 4.3V, 4.3V CV to 0.05C cut-off; 0.5C CC discharge to 2.5V; 25 plus or minus 2 degrees C; with split; rest 30 min between cycles | Greater than or equal to 80% initial capacity at 300 cycles |
| Leakage Test | Fully charged, stored at 60 plus or minus 2 degrees C and 85 plus or minus 5% RH for 7 days | No leakage |
| High/Low Temperature Discharge Characteristic | Charge: 0.2C CC to 4.3V, 4.3V CV to 0.02C cut-off at 25 plus or minus 2 degrees C; Discharge: 0.2C CC to 2.0V at -20 plus or minus 2 degrees C, 0.2C CC to 2.0V at -40 plus or minus 2 degrees C, 0.2C CC to 2.5V at 55 plus or minus 2 degrees C | Greater than 80% initial capacity at -20 plus or minus 2 degrees C; Greater than 60% initial capacity at -40 plus or minus 2 degrees C; Greater than 95% initial capacity at 55 plus or minus 2 degrees C |
| External Short Circuit Test | Fully charged, short-circuited with 20 milliohm resistor for 10 minutes, observed 1 hour at room temperature | No explosion and no fire |
| Over-Discharge Test | Fully discharged, 1C CC discharge for 90 minutes after standard charge, observed 1 hour | No explosion, no fire, and no leakage |
| Crush Test | Fully charged, crushed with 75mm half cylinder at less than or equal to 2mm/s until voltage reaches 0V or deformation reaches 15% or pressure reaches 100kN, observed 1 hour | No explosion and no fire |
| Overcharge Test | Fully charged, 1C CC charge to 1.1 times max charge voltage or 115% SOC, observed 1 hour | No explosion and no fire |
| Drop Test | Fully charged, dropped from 1.0m height onto concrete floor with terminals facing down, observed 1 hour | No explosion, no fire, and no leakage |
| Saltwater Immersion Test | Fully charged, immersed in 3.5% NaCl solution for 2 hours | No explosion and no fire |
| Low Pressure Test | Fully charged, stored at 11.6kPa and room temperature for 6 hours, observed 1 hour | No explosion, no fire, and no leakage |
| Temperature Cycling Test | Fully charged, cycled 5 times between -40 degrees C and 85 degrees C, observed 1 hour | No explosion, no fire, and no leakage |
| Storage Performance | Stored for 30 days at 25 plus or minus 2 degrees C and 65 plus or minus 20% RH | Residual capacity greater than or equal to 90% of initial capacity |
In a planning example, a platform drawing 100a at cruise from the 123.0Ah typical capacity can estimate about 1.2hours of continuous operation, while a 20ah baseline gives a much shorter window. The 2.0C continuous rating corresponds to approximately 240a, the 3.0C/30s pulse rating to approximately 360a, and the 0.5C charge rating to approximately 60a. Shipment voltage is controlled at 3.25v to 3.65v, and the low ACIR supports efficient energy transfer under these current levels.
For pack integration, pair the cell with a matching BMS, thermal sensing and mechanical protection. Confirm busbar current capability, heat dissipation, waterproof and dustproof requirements for the target airframe. The cell format can be arranged in multi-cell battery pack architectures where capacity and current headroom are balanced against weight and volume.
Jianheng provides quality assurance under the contract terms. Buyers should inspect voltage, self-discharge, internal resistance and appearance within 15 days of receipt and confirm potential defects with Jianheng. Damage from customer assembly after shipment is outside the assurance scope. Integration requires thermal sensors and BMS monitoring, and complete BMS records are needed for warranty review. Product liability follows contract terms. Jianheng may revise specifications and maintenance characteristics without prior notice.
The OID13119358-120000mAh-3.7V-3C-0112 cell is available from 1 piece. Certification includes UN38.3 and MSDS. Supply ability is 100000 pieces per month. Contact Jianheng for pricing, packaging, port details and customized drone battery pack solutions.